Command For Generating Rsa Key On Cisco Switch
Q: I have a Cisco switch in my network, which I can access by hooking up a console cable directly to the device. I like to access the switch remotely using SSH. How can I enable ssh on my Cisco 3750 Catalyst Switch?
A: By default, when you configure a Cisco device, you have to use the console cable and connect directly to the system to access it. Follow the steps mentioned below, which will enable SSH access to your Cisco devices. Once you enable SSH, you can access it remotely using PuTTY or any other SSH client.
1. Setup Management IP
Mar 27, 2017 Use this command to generate RSA key pairs for your Cisco device (such as a router). RSA keys are generated in pairs—one public RSA key and one private RSA key. If your router already has RSA keys when you issue this command, you will be warned and prompted to replace the existing keys with new keys. We need configure SSH on a Cisco router or switch in order to access it remotely, unless we’re using an access server. Even then, SSH should be configured in case the access server fails. # crypto key generate rsa modulus 1024 label C1801 The name for the keys will be: C1801% The key modulus size is 1024 bits. Most people believe that.
Jun 11, 2019 SW1 ( config)# crypto key generate rsa. How many bits in the modulus 512: 1024% Generating 1024 bit RSA keys, keys will be non-exportableOK Set the size of key to 1024 bits. If your Cisco Switch is running an older version of Cisco IOS image, then it is extremely recommended that you upgrade to latest Cisco IOS.
Jan 01, 2020 I then ran the crypto key generate rsa command to generate another key pair and still got the same end date. I then checked the version of my other switches in the network to see why they were not alerting about certificate end date and they were using iOS15.2.6 or later while this switch. On a 3560 switch running 12.2(25)SEA IOS, I've generated a crypto RSA exportable key. I'm following the directions in a document I found on CCO titled 'Configuring Secure Shell on Routers and Switches Running Cisco IOS'. Well I generated the key using: 'crypto key generate rsa general-keys exportab. Nov 21, 2016 R1(config)#crypto key generate rsa The name for the keys will be: R1.Technig.com Choose the size of the key modulus in the range of 360 to 2048 for your General Purpose Keys. Choosing a key modulus greater than 512 may take a few minutes. How many bits in the modulus 512: 1024% Generating 1024 bit RSA keys, keys will be non-exportableOK. Run show crypto key mypubkey rsa to see if you do, in fact, have a key fully generated and registered under a non-default name. If there is, then you can tell the ssh process to use this key with ip ssh rsa keypair-name xxx. If the first command doesn't show anything useful then I'd say you can go ahead and generate a new key.
First, make sure you have performed basic network configurations on your switch. For example, assign default gateway, assign management ip-address, etc. If this is already done, skip to the next step.
In the following example, the management ip address is set as 192.168.101.2 in the 101 VLAN. The default gateway points to the firewall, which is 192.168.101.1
2. Set hostname and domain-name
Next, make sure the switch has a hostname and domain-name set properly. /ssh-rsa-generate-public-key-from-private-key.html.
3. Generate the RSA Keys
The switch or router should have RSA keys that it will use during the SSH process. So, generate these using crypto command as shown below.
Also, if you are running on an older Cisco IOS image, it is highly recommended that you upgrade to latest Cisco IOS.
4. Setup the Line VTY configurations
Setup the following line vty configuration parameters, where input transport is set to SSH. Set the login to local, and password to 7.
If you have not set the console line yet, set it to the following values.
5. Create the username password
If you don’t have an username created already, do it as shown below.
Note: If you don’t have the enable password setup properly, do it now.
Make sure the password-encryption service is turned-on, which will encrypt the password, and when you do “sh run”, you’ll seee only the encrypted password and not clear-text password. commander keen 4 download mac
5. Verify SSH access
From the switch, if you do ‘sh ip ssh’, it will confirm that the SSH is enabled on this cisco device.
After the above configurations, login from a remote machine to verify that you can ssh to this cisco switch.
In this example, 192.168.101.2 is the management ip-address of the switch.
If you enjoyed this article, you might also like.
Create Rsa Key On Cisco Switch
Next post: How to Backup Oracle Database using RMAN (with Examples)
Command For Generating Rsa Key On Cisco Switch Download
Previous post: How to Use C++ Single and Multiple Inheritance with an Example Rsa encryption private key generation.